2.1 ch Soundbar with Bluetooth / Included components may vary by country or region of purchase: SA-WCT370, RM-ANP114, RM-ANP115, RM-ANP116, SA-CT370 Specifications HT-CT370. I am using teac a-h500i + monitor audio gold 100 + Sony SA-WMS7 in the same configuration, and it's working PERFECT. I highly recommend HIGH level input compared to LOW Level input. The sound is much more detailed.

Read Sony SA-VE702 / SA-VE705 / SA-WMS7 / SS-MS7 Service Manual online

Sony Sa Wms7 User Manual Download

Sony Sa Wms7 User Manual Pdf

SA-VE812ED/VE815ED/ WMS815/SS-MS815

US Model

Canadian Model

AEP Model

UK Model

E Model

SPECIFICATIONS

For the U.S. model

AUDIO POWER SPECIFICATIONS

POWER OUTPUT AND TOTAL HARMONIC DISTORTION :

with 8 Ω loads both channels driven, from 20 - 150Hz; rated 150 W per channel minimum RMS power, with no more than 0.8% total harmonic distortion from 250 mW to rated output.

SS-MS815 (front, center, and rear speakers)

Acid pro 6 serial number. Dimensions (w/h/d)

When attached speaker grilles:

Approx. 86 × 169 × 130 mm (31/2 × 63/4 × 51/8 in.) each

When attached to supplied speaker stand: Approx. 96 × 207 × 141 mm (37/8 × 81/4 × 55/8 in.) each, (Front (and rear)speakers) Approx. 169 × 131 × 144 mm (63/4 × 51/4 × 53/4 in.),

(Center speaker: pointed upwards) Approx. 169 × 118 × 141 mm (63/4 × 43/4 × 55/8 in.),

(Center speaker: pointed downwards):

Mass

When attached speaker grilles:

Approx. 1.3 kg (2lb 14oz) each

When attached to supplied speaker stand:

Approx. 1.4 kg (3lb 1oz) each, (Front (and rear) speakers) Approx. 1.4 kg (3lb 1oz), (Center speaker)

SA-WMS815 (subwoofer)

Continuous RMS power output

150 W (8 Ω, 20 - 150 Hz, 0.8 % THD)

Reproduction frequency range

24 Hz - 150 Hz

Windows embedded ce 6 0 media player download. Inputs

LINE IN (input pin jack) SPEAKER IN (input terminals)

Outputs

LINE OUT (output pin jack) SPEAKER OUT (output terminals)

General

Supplied accessories

SA-VE815ED

Speaker stands (for the front and rear speakers) (4) Speaker stand (for the center speaker) (1)

Screws (for the speaker stands) (10) Washers (for the speaker stands) (10)

Plates (for the front and rear speaker stands) (4) Speaker grilles (5)

Audio connecting cord (1)

Speaker connecting cords, 2.5 m (8 ft 21/2 in.) (5) Speaker connecting cords, 10 m (32 ft 93/4 in.) (2)

SA-VE812ED

Speaker stands (for the front speakers) (2) Screws (for the speaker stands) (4) Washers (for the speaker stands) (4) Plates (for the front speaker stands) (2) Speaker grilles (2)

Audio connecting cord (1)

Speaker connecting cords, 2.5 m (8 ft 21/2 in.) (4)

Design and specifications are subject to change without notice

SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below.

LEAKAGE

The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes). Leakage current can be measured by any one of three methods.

1.A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers’ instructions to use these instruments.

2.A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job.

3.Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2V AC range are suitable. (See Fig. A)

To Exposed Metal

Parts on Set

Earth Ground

Fig. A. Using an AC voltmeter to check AC leakage.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK !OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS

LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!

LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE ! SUR LES

DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

SECTION 1

GENERAL

• Location of Controls

SA-WMS7

– Front view –

– Rear view –

LINE IN/OUT jack

SPEAKER IN/OUT terminal

POWER SAVE switch

SA-VE812ED/VE815ED/WMS815/SS-MS815

SECTION 2

DIAGRAMS

2-1. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

Note on Printed Wiring Board:

•X: parts extracted from the component side.

•b: Pattern from the side which enables seeing. (The other layers' patterns are not indicated.)

•Indication of transistor.

Q

B C E

These are omitted.

Note on Schematic Diagram:

•All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums.

•All resistors are in Ω and 1/4 W or less unless otherwise specified.

•2: nonflammable resistor.

•C: panel designation.

•U : B+ Line.

•V : B– Line.

•Voltages are dc with respect to ground under no-signal conditions.

no mark : AUDIO

•Voltages are taken with a VOM (input impedance 10 MΩ).

Voltage variations may be noted due to normal production tolerances.

•Signal path.

F : AUDIO

•Abbreviation

CND : Canadian model

G : German model

•Circuit Boards Location SA-WMS815

POWER board

POWER SWITCH board

LED board

MAIN board

Sony Sa Wms7 Manual

CONTROL board

AUTO POWER board

Sony Sa Wms7 User Manual Online

SA-VE812ED/VE815ED/WMS815/SS-MS815

2-2. SCHEMATIC DIAGRAM • See page 7 for IC Block Diagrams.

A

Sony Sa Wms7 User Manual

B

C

D

E

Sony Sa Wms7 User Manual Free

F

G

•Semiconductor

Location

Ref. No. Location

5 5